Gas Springs for RV Compartments & Storage
Smooth Lift Support For RV And Camper Storage
RV compartment gas springs support storage hatches, camper doors, bed lift mechanisms, service panels, and travel vehicle compartments. They help users open and hold lids while keeping the motion controlled during travel and daily use.
Choose Gas Struts For Travel Conditions
RV gas struts should be selected by hatch weight, mounting geometry, stroke, extended length, compressed length, end fittings, vibration exposure, outdoor corrosion risk, and available installation space. Custom force and fitting combinations can be reviewed for OEM camper projects.
RV And Camper OEM Selection Details
Camper compartment gas springs must balance smooth opening with travel vibration, compact mounting space, weather seals, and lightweight panel stiffness. Provide hatch weight, hinge offset, open angle, bracket location, stroke, finish preference, and quantity so the gas strut supports storage doors, bed lifts, and service hatches without damaging hinges.
RV Compartment Gas Spring Selection Guide
RV compartment gas springs support camper storage doors, service panels, bed lift mechanisms, and exterior hatches. Travel vibration, outdoor weather, and compact installation space make these projects different from indoor cabinet hardware.
Best-Fit Uses
- Camper and motorhome exterior storage hatches.
- RV bed lift mechanisms and interior storage panels.
- Service doors on travel trailers and specialty vehicles.
Recommended Product Types
- Lift gas springs for compartment doors and storage lids.
- Dampers where soft closing is preferred.
- Stainless or corrosion-resistant options for exterior compartments.
What To Send For RFQ
- Door weight, hinge direction, open angle, and available space.
- Travel vibration, weather exposure, and expected operating temperature.
- Existing sample dimensions if replacing an RV strut.
- End fitting style, quantity, and finish preference.
Technical Specifications
| Specification | Reference Options - Confirm by Project |
|---|---|
| Force Range (F1) | 40N (Cabinets) to 1200N (Bed Lifts) |
| Rod Diameter | 6mm, 8mm, 10mm |
| Tube Diameter | 15mm, 18mm, 22mm |
| Surface Treatment | Black Nitride, QPQ, or SS304/SS316 |
| Operating Temperature | Confirmed for the selected seal, oil, and vehicle conditions |
| Damping Feature | Hydraulic deceleration on extension |
Frequently Asked Questions
How do I know what size gas spring I need for my RV bed?
Weigh the mattress and bed frame together, measure the hinge position and mounting points, and calculate the force per strut. Bed lifts sit at the high end of the RV range, up to about 1200 N per strut in the reference specification.
Why won't my RV baggage door stay open anymore?
Gas springs gradually lose pressure over years of use and temperature cycling. If the door no longer stays open, the struts have lost force and should be replaced, ideally as a pair.
Can you match replacements for standard RV brands?
Replacements can be matched from the extended length, compressed length, stroke, force marking, and fittings of the original strut. Fit is confirmed after measurement.
Will coastal salt air damage these gas springs?
Standard steel struts can corrode in salt air. Stainless steel versions are recommended for RVs that spend significant time near the ocean.
How should I install a new gas spring on an exterior compartment?
Rod-down orientation when closed is commonly preferred for standard gas springs, but the correct direction depends on the product and damping design. Follow the approved installation drawing.
Can I install a stronger strut on my baggage door?
It is not recommended to exceed the original force rating significantly. Too much force can bow a lightweight RV door and strain the hinges, making it difficult to close.
Do you supply custom lengths for camper van conversions?
Custom lengths and forces can be made to the storage geometry. Send the dimensions, panel weight, mounting points, and quantity.
Do the mounting brackets come with the gas springs?
Brackets, ball studs, and eyelets can be reviewed with the gas spring. Fit must be confirmed from the mounting surface, load path, articulation, fasteners, and drawing.