LX Gas Spring Resource
Lockable Gas Spring Release Systems: Lever, Push-Button and Remote Cable Release
How a lockable gas spring locks and releases: internal valve, rigid vs elastic locking, lever, push-button, threaded, cable and dual-spring release systems.

This guide explains how lockable gas springs work and how each release system is chosen. To compare models and sizes, see lockable gas spring products.
Short answer: a lockable gas spring has a valve inside the piston. Pressing the release pin opens the valve so the rod can move; letting go closes it and the spring locks at that position. Rigid locking holds firmly; elastic locking gives slightly. The release pin is operated directly by a lever or push button, or remotely by a Bowden cable, which can also release two springs at once.
How the Locking Valve Works
A lockable gas spring has a release pin running through the centre of the piston rod to a valve in the piston. With the valve closed, oil or gas cannot pass from one side of the piston to the other, so the rod cannot move and the spring holds its position. Pressing the pin opens the valve; the spring then extends under its own force or can be pushed in by the user. Releasing the pin closes the valve again at the new position.

Lockable gas springs are used wherever a moving part must stop at any point, not only at full open: adjustable beds, treatment and office chairs, height-adjustable tables, seating, lift tables, and industrial adjustment panels.
Rigid vs Elastic Locking
In a rigid lockable gas spring, oil fills the locking chamber, so the locked position stays firm under load. In an elastic lockable gas spring, gas remains in the locking chamber, so the locked position gives slightly. Rigid locking is common for adjustable beds, height-adjustable tables, and equipment; elastic locking is common for chairs and recliners, where a little give feels more comfortable.
Release Systems: Lever, Push-Button and Remote Cable Release
| Release system | How it works | Typical use |
|---|---|---|
| Lever release | A lever presses the release pin at the rod end | Chairs, recliners, tables where the user can reach the spring |
| Push-button release | A button head on the rod end presses the pin | Compact mechanisms, equipment adjustment |
| Threaded release head | The release head screws onto a matching actuator | OEM mechanisms with their own release hardware |
| Bowden cable release | A handle pulls a cable that presses the pin remotely | Beds, seating, and furniture where the spring is hidden |
| Dual (one-to-two) cable system | One handle releases two lockable springs together | Wide backrests, beds, and tables that must move evenly |

Push-Button Release Lockable Gas Springs
A push-button release puts the button on the rod end, so the user presses it directly where the spring is mounted. It suits compact mechanisms within reach, such as equipment arms, tilting tops and adjustment panels. See the push-button release lockable gas spring.
Remote Cable Release Lockable Gas Springs
A remote cable release uses a Bowden cable from a handle or lever to the release head, so the spring can be hidden inside the mechanism while the handle sits where the user's hand is. One handle can release two springs together on wide seats, beds and covers. See the cable release lockable gas spring and the remote release lockable gas spring.
Cable Length and Release Force
With a cable release, the handle position, cable length, and routing all change how the release feels. Tight bends add friction and make the handle heavy; a cable that is too long or loosely routed can leave slack, so the pin does not open fully. Route the cable with gentle bends, fix it so it cannot be pinched by moving parts, and check release effort on a sample in the real mechanism.

Threaded and Custom Release Heads
Some OEM mechanisms supply their own release actuator. In that case, the lockable gas spring is made with a threaded release head that screws into the customer hardware, and the pin travel and actuation force are agreed on the drawing.

Selection Inputs
Send force, stroke, extended and compressed length, locking type (rigid or elastic), locking direction, end fittings, release type, handle or button location, cable length, and quantity. For seating or bed applications, also say whether the spring supports body weight, equipment weight, or positioning only.
Mounting geometry still matters: a lockable gas spring holds only within the limits of bracket strength, fitting alignment, and its locking force. Avoid side load and make sure the cable is not strained as the mechanism moves.
For guards and covers that must not drop during maintenance, see safety locking gas springs. Compare lockable gas spring products, see medical applications, or send your adjustment mechanism for a recommendation.
Frequently Asked Questions
How does a lockable gas spring lock?
A valve in the piston closes when the release pin is not pressed, so oil or gas cannot pass the piston and the rod stays in place.
What is the difference between rigid and elastic locking?
Rigid locking uses oil in the locking chamber and holds firmly; elastic locking keeps gas in the chamber and gives slightly under load.
Can one handle release two lockable gas springs?
Yes. A dual cable system releases two springs together, which keeps wide backrests, beds, and tables moving evenly.
Which release type is best?
It depends on where the user's hand is, how the mechanism is laid out, and the available cable route. Levers and push buttons suit reachable springs; cables suit hidden ones.
Can lockable gas springs be customized?
Yes. Stroke, force, length, fittings, release head, cable system, material, and finish can be made to OEM drawings.