LX Gas Spring Resource
Heavy-Duty Gas Springs: How to Select High-Force Gas Struts
How to select heavy-duty gas springs: force calculated per project, tube and rod size, buckling, metal fittings and brackets, steel or SS316, safety locks and an RFQ list.

Some lids, covers and hatches are simply too heavy for a standard gas spring: engine covers on machines, truck toolbox lids, container doors, large machine guards and heavy service hatches. A heavy-duty gas spring is not a special product family so much as a set of choices: more force, a larger tube and rod, stronger end fittings and brackets, and often two springs instead of one. This guide shows how to select them.
Short answer: calculate the force per spring from the panel weight and geometry, then choose a size that carries it with margin: larger tube and rod diameters for high force and long stroke, metal eyelets or clevis forks rather than plastic sockets, stiff brackets, and two springs on wide or heavy panels. LX lift gas springs are made up to about 2,500 N per spring, with 22/10 mm and 28/14 mm tube/rod sizes for heavy panels; the force for each project is calculated from the drawing, not taken from a catalogue maximum.
When You Need a Heavy-Duty Gas Spring
- The panel is heavy or deep, so the moment about the hinge is large.
- The mounting point has to sit close to the hinge, which multiplies the force needed.
- The equipment vibrates, works outdoors or is opened many times a day.
- The panel is wide, so a single spring would twist it.
If the calculated force per spring is very high, first look at the geometry: moving the mounting point further from the hinge often brings the force down more than a larger spring would. The mounting position calculation shows how.
Force: Calculated Per Project
Use F = m × 9.81 × d / (n × L), where L is the effective lever arm, and add a margin for friction and cold weather. The force calculator does this in N and lbf. Example from heavy equipment: a 60 kg engine cover with its centre of gravity 400 mm from the hinge and a 120 mm lever arm needs about 981 N per spring with two springs, about 1,130 N with a 15% margin; one spring alone would need about 1,960 N on a single bracket. See heavy equipment gas springs.
Tube and Rod Size, Stroke and Buckling
High force needs a larger rod and tube, and a long stroke makes the rod more slender when fully extended. A heavy, long gas spring that is too thin can bend if it is side-loaded or used as an end stop. Keep the stroke no longer than the motion needs, use the larger diameters for high force, and make sure the spring is never the part that stops the lid.
| Panel | Typical starting point |
|---|---|
| Medium covers and lids | 18/8 mm tube/rod, often in pairs |
| Heavier hatches and truck toolbox lids | 22/10 mm, usually two springs |
| Heavy-duty panels and engine covers | 28/14 mm, two springs, metal fittings |
Final sizes are confirmed from the force, stroke and lengths calculated for the project.
End Fittings and Brackets
Heavy springs put high loads into the mounting points. Metal eyelets and clevis forks carry more load than plastic ball sockets and keep the spring in one plane; metal ball joints suit mounts where the angle changes. Brackets must be stiff enough not to flex and well anchored; on thin sheet, add a reinforcement plate. Misaligned brackets create side load, which wears the seal and can bend the rod. See the end fittings guide.
Steel or Stainless Steel
Painted steel tubes with QPQ-treated or chrome-plated rods suit most indoor and protected equipment. For outdoor, coastal or washdown use, SS316 stainless steel gas springs with stainless fittings and brackets resist corrosion; see the SS316 heavy-duty gas spring and stainless steel gas springs.
Safety: Locks, Props and Hold-Open
A gas spring that loses force can let a heavy panel fall. Where people work under a heavy lid or guard, add a mechanical prop, a locking tube or a safety clip, or use a lockable gas spring that holds at any position. The machine risk assessment decides which is needed. See safety gas springs.
Heavy-Duty Gas Springs for Trucks
Truck toolbox lids, service bodies and tonneau covers add road vibration, cold weather and road salt. They typically use 8/18 mm or 10/22 mm springs in pairs, sized for the coldest working temperature, with metal fittings. See heavy duty truck gas springs.
RFQ List for Heavy-Duty Gas Springs
- Panel weight, size and centre of gravity
- Hinge position and the two mounting points (closed and open)
- Opening angle, stroke, extended and compressed length
- Number of springs and the space available for each
- End fittings and bracket material and thickness
- Environment: outdoor, vibration, temperature range, salt or washdown
- Safety requirement: prop, lock or lockable spring
- Quantity and sample needs
LX Gas Spring has 20+ years of manufacturing, an ISO 9001 quality system, a TÜV fatigue test of 180,000 cycles and a 3-year warranty on all gas springs. Request a quote with your drawing.
Frequently Asked Questions
What is a heavy-duty gas spring?
A gas spring sized for a heavy load: higher force, larger tube and rod, metal end fittings and stiff brackets, usually used in pairs on large covers, hatches and lids.
How much force can a heavy-duty gas spring have?
LX lift gas springs are made up to about 2,500 N per spring. The force for a project is calculated from the panel weight and mounting geometry; if it comes out too high, change the geometry or use more springs.
Should I use one heavy spring or two smaller ones?
Usually two. Two springs share the load, keep a wide panel from twisting and reduce the load on each bracket.
Do heavy-duty gas springs need a safety device?
Where people work under the panel, yes: add a prop, locking tube, safety clip or a lockable gas spring, as the risk assessment requires.